PassLeader Supply The Latest Cisco 200-101 PDF And VCE Briandumps For Free Download (51-60)

Comments are closed

QUESTION 51
Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0? (Choose two.)

A.    Router(config)# router ospf 0
B.    Router(config)# router ospf 1
C.    Router(config)# router ospf area 0
D.    Router(config-router)# network 192.168.16.0 0.0.0.255 0
E.    Router(config-router)# network 192.168.16.0 0.0.0.255 area 0
F.    Router(config-router)# network 192.168.16.0 255.255.255.0 area 0

Answer: BE
Explanation:
In the router ospf
command, theranges from 1 to 65535 so o is an invalid number – B is correct but A is not correct. To configure OSPF, we need a wildcard in the “network” statement, not a subnet mask. We also need to assgin an area to this process – E is correct.

QUESTION 52
Which type of EIGRP route entry describes a feasible successor?

A.    a backup route, stored in the routing table
B.    a primary route, stored in the routing table
C.    a backup route, stored in the topology table
D.    a primary route, stored in the topology table

Answer: C
Explanation:
Feasible successor is a route whose Advertised Distance is less than the Feasible Distance of the current best path. A feasible successor is a backup route, which is not stored in the routing table but stored in the topology table.

QUESTION 53
Which command displays the CHAP authentication process as it occurs between two routers?

A.    debug chap authentication
B.    debug authentication
C.    debug chap ppp
D.    debug ppp authentication

Answer: D

QUESTION 54
A department decides to replace its hub with a Catalyst 2950 switch that is no longer needed by another department. To prepare the switch for installation, the network administrator has erased the startup configuration and reloaded the switch. However, PCs that are connected to the switch experience various connectivity problems. What is a possible cause of the problem?

A.    The VLAN database was not erased.
B.    The management VLAN is disabled.
C.    The running configuration should have been erased.
D.    The “mode” button was not pressed when the switch was reloaded.
E.    The switch was not configured with an IP address or a default gateway.

Answer: A

QUESTION 55
Which two statements describe characteristics of IPv6 unicast addressing? (Choose two.)

A.    Global addresses start with 2000::/3.
B.    Link-local addresses start with FE00:/12.
C.    Link-local addresses start with FF00::/10.
D.    There is only one loopback address and it is ::1.
E.    If a global address is assigned to an interface, then that is the only allowable address for the interface.

Answer: AD


PassLeader[12]

http://www.passleader.com/200-101.html

QUESTION 56
What are three features of the IPv6 protocol? (Choose three.)

A.    optional IPsec
B.    autoconfiguration
C.    no broadcasts
D.    complicated header
E.    plug-and-play
F.    checksums

Answer: BCE

QUESTION 57
A router has two Fast Ethernet interfaces and needs to connect to four VLANs in the local network. How can you accomplish this task, using the fewest physical interfaces and without decreasing network performance?

A.    Use a hub to connect the four VLANS with a Fast Ethernet interface on the router.
B.    Add a second router to handle the VLAN traffic.
C.    Add two more Fast Ethernet interfaces.
D.    Implement a router-on-a-stick configuration.

Answer: D

QUESTION 58
Select the action that results from executing these commands.
Switch(config-if)# switchport port-security
Switch(config-if)# switchport port-security mac-address sticky

A.    A dynamically learned MAC address is saved in the startup-configuration file.
B.    A dynamically learned MAC address is saved in the running-configuration file.
C.    A dynamically learned MAC address is saved in the VLAN database.
D.    Statically configured MAC addresses are saved in the startup-configuration file if frames from that address are received.
E.    Statically configured MAC addresses are saved in the running-configuration file if frames from that address are received.

Answer: B

QUESTION 59
Which two of these statements are true of IPv6 address representation? (Choose two.)

A.    There are four types of IPv6 addresses: unicast, multicast, anycast, and broadcast.
B.    A single interface may be assigned multiple IPv6 addresses of any type.
C.    Every IPv6 interface contains at least one loopback address.
D.    The first 64 bits represent the dynamically created interface ID.
E.    Leading zeros in an IPv6 16 bit hexadecimal field are mandatory.

Answer: BC

QUESTION 60
What are two enhancements that OSPFv3 supports over OSPFv2? (Choose two.)

A.    It requires the use of ARP.
B.    It can support multiple IPv6 subnets on a single link.
C.    It supports up to 2 instances of OSPFv3 over a common link.
D.    It routes over links rather than over networks.

Answer: BD


PassLeader Supply The Latest Cisco 200-101 PDF And VCE Briandumps For Free Download

http://www.passleader.com/200-101.html

         

Comments are closed.